SOFTWARE -> HAPCAN PROGRAMMER
HAPCAN Programmer is the Windows based software which sets up the HAPCAN system. Computer can be connected to the system using RS232C or Ethernet interface. Whole setting up process can be done through the system network, or even through the Internet. It means that devices do not have to be preconfigured before installing.
Version:
-
2.85
Features:
-
searching for devices on the HAPCAN network;
-
node basic settings (ID and descriptions);
-
controlling nodes;
-
linking devices, it sets relationships between nodes;
-
firmware update of nodes;
-
saving node configuration to a file (saves ID, description and linking information);
-
monitor tool displays messages sent by nodes on the bus.
Controlled devices:
|
Module |
Hardware |
Firmware |
|||
|
RS232C Interface |
UNIV 2.0.1.0 UART 2.1 |
UNIV 2.0.1.0 UART 2.1.1.2 |
|
||
|
Ethernet Interface |
UNIV 2.0.2.0 ETH 1.0 |
UNIV 2.0.2.0 ETH 1.0.1.3 |
|
||
|
Button |
UNIV 1.0.1.0 UNIV 1.0.1.2 UNIV 1.0.1.3 BUTT 2.1 BUTT 2.3 |
UNIV 1.0.1.0 UNIV 1.0.1.2 UNIV 1.0.1.3 BUTT 2.1.1.3 BUTT 2.2.1.3 |
UNIV 1.0.1.21 UNIV 1.0.1.31
|
UNIV 1.0.1.33 |
|
|
|
Relay |
UNIV 1.0.2.0 UNIV 1.0.2.1 UNIV 1.0.2.2 UNIV 1.0.2.3 UNIV 1.0.2.4 REL 2.2 REL 2.3 |
UNIV 1.0.2.0 UNIV 1.0.2.1 UNIV 1.0.2.2 UNIV 1.0.2.3 UNIV 1.0.2.4 REL 2.2.1.3 REL 2.3.1.4 |
UNIV 1.0.2.10 UNIV 1.0.2.11 UNIV 1.0.2.21 |
UNIV 1.0.2.22 |
|
|
Infrared Receiver |
UNIV 1.0.3.0 UNIV 1.0.3.2 IRRX 2.2 |
UNIV 1.0.3.0 UNIV 1.0.3.2 IRRX 2.2.1.3 |
||
|
|
Temperature Sensor |
UNIV 1.0.4.0 | UNIV 1.0.4.0 | ||
|
|
Infrared Transmitter |
UNIV 1.0.5.0 | UNIV 1.0.5.0 | UNIV 1.0.5.1 | |
|
|
Dimmer |
UNIV 1.0.6.0 UNIV 1.0.6.2 DIM 2.1 |
UNIV 1.0.6.0 UNIV 1.0.6.2 DIM 2.1.1.4 |
UNIV 1.0.6.1 UNIV 1.0.6.21 DIM 2.1.1.5 |
UNIV 1.0.6.11 UNIV 1.0.6.22
|
|
|
Blind Controller |
UNIV 1.0.7.1 | UNIV 1.0.7.1 | ||
|
LED Controller |
UNIV 1.0.8.1 |
UNIV 1.0.8.1 |
UNIV 1.0.8.11 | UNIV 1.0.8.12 | |
Platform:
-
Windows XP/Vista/7
-
minimum resolution 1024x768
 |
HAPCAN285.exe 1.25MB - freeware. |
Screenshots:
 |
 |
 |
| searching for devices on the network | general data of node | firmware update |
 |
 |
 |
| dimmer control | dimmer configure | monitor |
|
Searching for nodes on the network |
||||
| Preliminary settings |
Software settings (menu->Tools->Settings). |
|||
|
Programming process |
|
|||
|
Node basic settings |
||||
| Preliminary settings |
Searching for nodes on the network. |
|||
|
Programming process |
Setting up the node identifier and description.
|
|||
|
Firmware update |
||||
| Preliminary settings |
Searching for nodes on the network. |
|||
|
Programming process |
|
|||
|
Dimmer control |
||||
| Preliminary settings |
Searching for nodes on the network. |
|||
|
Programming process |
Turn the dimmer softly on at 100% in 5s after pressing the button.
|
|||
|
Linking devices |
||||
| Preliminary settings |
Searching for nodes on the network. Node basic settings. |
|||
|
Aim |
This example shows how to set up the relationship between two devices: relay and button nodes. 1. The relay to be turned on when button 1 is pressed. 2. The relay to be toggled when button 2 is pressed. 3. The relay to be turned off when button 3 is pressed.
|
|||
|
Programming process |
|
|||
